Clamping Washer Tool For Ford Washer 6715468 More ITEM # TL-CW001 For the quick and safe removal / fitting of clamping washers commonly used on underbody heat shields For use with 1/4" wrench Was: MSRP: Now: $22.00 View Details
Disc Brake Piston Caliper Cube Tool More ITEM # TL-DBP03 For use on popular domestic and import with 4 wheel disc brakes Removes, re-installs, and re-aligns caliper pistons For use with 3/8" drive ratchet Was: MSRP: Now: $9.00 View Details
Strut Rod Bushing Set 1967-1973 Mercury Cougar, 1968-1971 Ford Torino, 1966-1967 Mercury Comet, 1967-1973 Ford Mustang, 1966-1970 Ford Falcon, 1966-1970 Ford Fairlane More ITEM # FM-ES017E OE # C6OZ-3A187-A OE-spec replacement installs on threaded end of strut rod at front and rear sides of the chassis mount Helps maintain proper firmness of the front suspension when in motion For installation on either driver or passenger side; Restores original appearance and functionality when replacing a failed or aging component Was: MSRP: Now: $39.00 View Details
Door Panel Removal Tool Straight More ITEM # TL-DPR01 Notched head reaches between door panel and door sheetmetal to release attachment clips Avoids damage to panel by spreading leverage force over a wider area than without using tool Ergonomic handle has hang hole and molded grip integrated into its construction Was: MSRP: Now: $13.00 View Details
Door Panel Removal Tool Curved More ITEM # TL-DPR02 Notched head reaches between door panel and door sheetmetal to release attachment clips Avoids damage to panel by spreading leverage force over a wider area than without using tool Ergonomic handle has hang hole and molded grip integrated into its construction Was: MSRP: Now: $18.00 View Details
Ford / Mopar Fuel Tank Sending Unit Lock Ring Removal Tool 2 1/8" ID More ITEM # TL-FSU01 Tool enables easier removal and installation of lock ring when replacing the fuel sending unit. Handle provides additional leverage without risk of damage that could otherwise happen if using hammer and punch. Longer angled handle also reduces "knuckle scraping". Correct tooth pattern allows for full engagement of lock ring circumference. Slotted area allows you to slip past tubes and wires with ease. Was: MSRP: Now: $21.00 View Details
Ford Headlight Adjusting Ratchet Wrench, 4mm Hex More ITEM # TL-HAW01 4mm hex head is sized for the rear-mounted adjusters on headlights 10" handle clears obstructions and provides leverage to use ratcheting mechanism in head Note: 94 to 98 Mustangs require radiator cover to be removed for access to the headlight adjusters Was: MSRP: Now: $27.00 View Details
Gauge Tester For 1955-1986 Ford Vehicles With 73-10 Ohm More ITEM # TL-GT001 Test the function and accuracy of Fuel, Temperature, and Oil Pressure gauges. Simple slide switch lets you test gauges at high, medium and low readings. Designed to work specifically with your 1955-1986 Ford Vehicle with ohm range of 73-10 with non-linear coil resistance. Instrument cluster gauges can be tested without being completely removed from vehicle by testing at sending unit location. Was: MSRP: Now: $35.00 View Details
Saginaw Steering Column Pivot Pin Remover Tool More ITEM # TL-SPP01 Aids in pressing retaining pin out of Saginaw type tilt & telescopic steering columns Was: MSRP: Now: $9.00 View Details
Dana 44 Ball Joint Spanner Wrench Socket For 1/2 Ton, 3/4 Ton, and 1 Ton More ITEM # TL-BJS01 Designed for installation / removal of Dana 44 open yoke front axle pre-load adjusting sleeves Compatible with 1/2 Ton, 3/4 Ton, and 1 Ton Dana 44 open yoke front axles. For use with many Chrysler, Ford, GM, International, Jeep 4WD vehicles. Allows for proper torque of adjusting sleeves to attain correct pre-load on ball joint with 1 inch socket Was: MSRP: Now: $18.00 View Details
Pitman Arm or Tie Rod End Puller Separator Tool 1-1/16 inch (27mm) More ITEM # TL-PAP01 Aids in seperating pitman arm from sector shaft Can be used to separate tie rod ends on applicable vehicles Pitman arm slot opening 1.8" (46mm); Sector Shaft opening 1.06" (27mm); Pull length 2.7" (68mm) Was: MSRP: Now: $17.00 View Details
Pitman Arm or Tie Rod End Puller Separator Tool 1-11/32 inch (33mm) More ITEM # TL-PAP02 Aids in seperating pitman arm from sector shaft Can be used to separate tie rod ends on applicable vehicles Pitman arm slot opening 2.5" (64mm); Sector Shaft opening 1.3" (33mm); Pull length 2.7" (68mm) Was: MSRP: Now: $17.00 View Details
